Federal Pacific panels: what home buyers should know
Federal Pacific panels with Stab-Lok breakers have a troubled record: CPSC testing confirmed the breakers fail certain UL tests, though the agency closed its case in 1983 without deciding whether they're safe, and there's been no U.S. recall. If the house you're buying has one, ask an electrician to look at it during your due diligence period.
The doubts are about the breakers and whether they trip when a circuit is overloaded. A New Jersey court's class action notice says the court found the maker cheated during its testing for UL approval, yet how often the breakers fail in real homes is still disputed.
Are Federal Pacific panels dangerous?
The CPSC never gave an official yes or no, so it helps to separate what's documented from what's still argued.
On the record:
- The CPSC's investigation from 1980 to 1983, in which its testing confirmed that the breakers fail certain UL calibration tests.
- A New Jersey court's class action notice, which says the court had already determined that Federal Pacific violated the state's Consumer Fraud Act because the company "cheated during its testing of circuit breakers" to get UL approval. The notice was addressed to New Jersey homeowners, and its deadline for claims was April 20, 2005.
- A 1982 Securities and Exchange Commission filing by Reliance Electric, the company's parent, saying the breakers' UL listings "have previously been obtained through the use of deceptive and improper practices," as NBC Bay Area quoted it in 2012.
Still argued:
- How often the breakers fail. One insurer's 2019 safety sheet says testing from 1979 to 1983, by the CPSC, at least four companies and independent testers, found failures to trip in 14 to 74 percent of tests. With results that far apart, no single number is the failure rate.
- How many fires they cause. An engineer who has testified in lawsuits against the company believes they cause about 2,000 fires a year nationwide, NBC Bay Area reported in 2012. That's one expert's estimate, not a count.
- The maker's position, as the CPSC recorded it: the breakers trip reliably at most overload levels, and at the few levels where they may not, the current is too low to make dangerous heat. The CPSC said it couldn't accept or refute that.
What did the CPSC find about Stab-Lok breakers?
The investigation began in June 1980, the CPSC's 1983 release says, when Reliance Electric, which had bought Federal Pacific in 1979, told the agency that many of the company's breakers didn't fully comply with UL requirements.
The CPSC's own testing confirmed that the breakers fail certain UL calibration tests. It focused mainly on two-pole residential breakers made before Reliance bought the company.
In March 1983, the Commission closed the two-year investigation because the data then available didn't establish a serious risk of injury.
It said it was unable at that time to link the test failures to a hazardous situation, and that its staff had insufficient data to accept or refute the maker's position. It cited its limited budget and the cost of a further study, and said it could reopen the case.
In 2011, the CPSC added a note to the top of that release. It asks electricians, homeowners, home inspectors and real estate agents to "read and interpret the following press release carefully."
The note also says the Commission closed the matter "without making a determination as to the safety of FPE circuit breakers or the accuracy of the manufacturer's position." So the release isn't a finding that the panels are dangerous, and it isn't a clean bill of health either.
How to spot a Federal Pacific panel
Start with the label, and leave the cover on. Insurers and news reports date these panels from about the 1950s into the 1980s, so check the panel itself instead of guessing from the house's age.
One insurer's July 2025 loss-control article says to look for a "Federal Pacific" or "FPE" label on the front of the panel. Stab-Lok breakers are painted red, it says, and the word "Stab-Lok" appears on the panel face or on the label inside the cover door, usually near the top.
An inspector's reference site adds that the label may read "FPE," "FP," "Federal Pacific," "Federal Electric" or "Federal Pioneer," the Canadian brand of the same design. The word "Stab-Lok" isn't on every panel, it says, and the panel has to be a breaker panel, not a fuse panel.
Inside, the bus bar design has E- or F-shaped cutouts, but only someone who removes the cover can see them, and the same reference warns that only an expert should take it off.
InterNACHI's standards have a home inspector inspect the panel and its breakers without requiring the cover to come off. The panel is on the electrical checklist of a home buyer inspection, and if the report flags a Federal Pacific, the next call is to an electrician.
Can you insure a house with a Federal Pacific panel?
Some insurers publish their view. The same July 2025 article says "almost every insurance company" has taken a stance against Federal Pacific breakers.
Whether a particular company will write or renew a homeowners policy on a house with one is that company's call. Ask your own insurance agent before closing, and ideally before your due diligence period ends, while there's still time to act on the answer.
A home inspection can't settle it: InterNACHI's standards say an inspection does not determine the insurability of the property.
Should you replace a Federal Pacific panel?
Two insurers' published advice is to replace it. The July 2025 article says its loss-control specialists recommend replacing the entire panel with a modern one, and another insurer's 2019 safety sheet recommends replacing all Stab-Lok panels and breakers with UL Listed equipment.
That's a job for an electrician, and these questions are worth asking:
- Is this a Federal Pacific breaker panel from the Stab-Lok family, going by the label, the breakers and what's behind the cover?
- Will you open the cover and look at the bus design yourself?
- What would replacing the whole panel involve, compared with swapping breakers?
- Will you write up the work in a way my insurance agent will accept?
Book that visit early. Our guide to earnest money and due diligence in Georgia explains how the period works, and our polybutylene plumbing guide and other home inspection guides cover more of what turns up in older houses.
Federal Pacific panel questions from home buyers
Can you just replace the breakers in a Federal Pacific panel?
One insurer's 2019 loss-control sheet recommends against it, even with UL-approved breakers, because a panel fitted with another brand's breakers hasn't been UL-tested as an assembly. An inspector's reference site also warns that counterfeit Stab-Lok breakers exist.
What should you do if a Federal Pacific breaker trips?
The CPSC's 1983 release gives advice that applies to any breaker: don't simply reset it. Find out why it tripped, and disconnect any product that develops problems.
Is every Federal Pacific breaker defective?
No. NBC Bay Area's 2012 investigation reported that not every Federal Pacific breaker is defective, and that some of the breakers were later modified and passed UL inspection. The concern centers on the Stab-Lok line.
Ready to book your home inspection?
Send a request with your town and deadline, pick a time yourself online, or call and we'll set a time.
